Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Bath electric heater
09-30-2006, 07:32
Post: #1
Bath electric heater
I removed and replaced my heater today. It still works and I just
wanted something newer. It is available to anyone for free- just pay
for postage. Ernie- 83PT40 in warm Montana
Quote this message in a reply
09-30-2006, 23:31
Post: #2
Bath electric heater
not a direct replacement, Jay. It happpens a few months ago I bought a little
space heater and it fit- the thing you have to look out for- is the total
height. I cut the wood at the top of the original frame and it had clearance. i
believe the clearance is 8 inches. The width can be up to 20 inches. also-
measure your depth, that is also a factor. Now I have endless heat.

Ernie Ekberg
83 PT40
Livingston, Montana



[Non-text portions of this message have been removed]
Quote this message in a reply
10-01-2006, 02:50
Post: #3
Bath electric heater
Ernie,
was the heater a direct replacement? Fit same hole as the old one?

Please tell me more!

My bath heater works, makes heat, but then a safety "over-heat" switch
doesn't allow it to run again for about 30 minutes. Gets cool in the
bathroom before the heater runs again. May need a new fan motor.

I'd like to replace it. Have not found the direct replacement yet.

Thanks
Jay Darst
85PT40
Springfield, IL



--- In WanderlodgeForum@yahoogroups.com, "Ernest Ekberg"
wrote:
>
> I removed and replaced my heater today. It still works and I just
> wanted something newer. It is available to anyone for free- just pay
> for postage. Ernie- 83PT40 in warm Montana
>
Quote this message in a reply
10-01-2006, 03:32
Post: #4
Bath electric heater
Hi Terry- will be home aorund 5 all this week. Come on over.

Ernie Ekberg
83 PT40
Livingston, Montana



[Non-text portions of this message have been removed]
Quote this message in a reply
10-01-2006, 04:03
Post: #5
Bath electric heater
Jay,etal: I replaced the motor on the Fasco fan in the Galley on RUBY
(the long narrow one, also I think Fasco calls it the under cabinet
or step), a while back. I got the motor from Grainger, I don't have
the part # in my Maint log, but I am sure you can find one. Pull the
heater and take the motor/fan and you can match it up.

If you go that route, then you will have to buy a new fan as well, if
I remember correctly, the shaft size was off. But no biggy there
(cept another trip to Grainger) either, the hardest part was
adjusting the fan so it did not hit anything. Works great. I prefer
the electric heat when we can need to use it much quieter.

Let me know if you have any problems I will (read have Judi) search
for the invoice.

ScottB
86FC35 "RUBY" 4 SALE
Murrells Inlet SC "right next to heaven"

--- In WanderlodgeForum@yahoogroups.com, "Jay Darst"
wrote:
>
> Ernie,
> was the heater a direct replacement? Fit same hole as the old one?
>
> Please tell me more!
>
> My bath heater works, makes heat, but then a safety "over-heat"
switch
> doesn't allow it to run again for about 30 minutes. Gets cool in
the
> bathroom before the heater runs again. May need a new fan motor.
>
> I'd like to replace it. Have not found the direct replacement yet.
>
> Thanks
> Jay Darst
> 85PT40
> Springfield, IL
>
>
>
> --- In WanderlodgeForum@yahoogroups.com, "Ernest Ekberg"
> wrote:
> >
> > I removed and replaced my heater today. It still works and I just
> > wanted something newer. It is available to anyone for free- just
pay
> > for postage. Ernie- 83PT40 in warm Montana
> >
>
Quote this message in a reply
10-01-2006, 04:07
Post: #6
Bath electric heater
Hi Ernie,

If you're going to be around this week, I'd like to try & stop in to
take a look at your bath electric heater replacement. Did you get your
heater at the Home Depot in Bozeman? I may check with Grainger in
Billings too since they carry all types. I need to do the same thing on
the PT40. Still making progress on all the refurbishment. Installing a
new microwave this week & all new roof vents. Almost ready for paint,
must happen before the snows start.

Terry Neal
Bozeman, MT
82PT40
74FC34



erniecarpet@... wrote:

> not a direct replacement, Jay. It happpens a few months ago I bought a
> little
> space heater and it fit- the thing you have to look out for- is the total
> height. I cut the wood at the top of the original frame and it had
> clearance. i
> believe the clearance is 8 inches. The width can be up to 20 inches.
> also-
> measure your depth, that is also a factor. Now I have endless heat.
>
> Ernie Ekberg
> 83 PT40
> Livingston, Montana
>
> [Non-text portions of this message have been removed]
>
>
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)