Post Reply 
 
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
HWH jack wont retract
12-30-2006, 13:14
Post: #1
HWH jack wont retract
The left front jack on my 88 FC wont fully retract. The piston returns
all the way but the knee action does not go to horizontal. I lubed all
the pivot points. Still wont return to horizontal. HWH trouble shooting
chart suggests the actuator may be at fault. I can get the jack to
retract by manually pushing it up to horizontal. I examined the
actuator rod and it does not appear bent or scored. It is stiff. Can
these be rebuilt or is it just better to get a new one? HWH web site
shows that actuator to be $150.00 OUCH ! I read where John Finn had
his whole system rebuilt for about $900 plus at the HWH factory. Almost
makes me want to do the whole works.

Bruce 88 FC35
Quote this message in a reply
12-30-2006, 15:27
Post: #2
HWH jack wont retract
Bruce,

Just replaced the actuator on my driver rear jack, did the same thing.

They have the reman. Units cheaper (around $80.00)..



Not too bad to change..



Good luck.

Stpehen H

81 FC-33 SB





_____

From: WanderlodgeForum@yahoogroups.com
[mailto:WanderlodgeForum@yahoogroups.com] On Behalf Of birdshill123
Sent: Saturday, December 30, 2006 8:15 PM
To: WanderlodgeForum@yahoogroups.com
Subject: [WanderlodgeForum] HWH jack wont retract



The left front jack on my 88 FC wont fully retract. The piston returns
all the way but the knee action does not go to horizontal. I lubed all
the pivot points. Still wont return to horizontal. HWH trouble shooting
chart suggests the actuator may be at fault. I can get the jack to
retract by manually pushing it up to horizontal. I examined the
actuator rod and it does not appear bent or scored. It is stiff. Can
these be rebuilt or is it just better to get a new one? HWH web site
shows that actuator to be $150.00 OUCH ! I read where John Finn had
his whole system rebuilt for about $900 plus at the HWH factory. Almost
makes me want to do the whole works.

Bruce 88 FC35





[Non-text portions of this message have been removed]
Quote this message in a reply
12-30-2006, 16:02
Post: #3
HWH jack wont retract
Bruce,
Check the pivot points closely, on my 87FC the hole for the pivot
bolt had rounded out and caused some binding, the spring was not
strong enough at that point to bring the jack up to the stored
position. I had to take the jack off (it's heavy) and weld the hole,
then re-drill to proper size.

Robert Britton
87FC
Hollister, California



--- In WanderlodgeForum@yahoogroups.com, "birdshill123"
wrote:
>
> The left front jack on my 88 FC wont fully retract. The piston
returns
> all the way but the knee action does not go to horizontal. I lubed
all
> the pivot points. Still wont return to horizontal. HWH trouble
shooting
> chart suggests the actuator may be at fault. I can get the jack to
> retract by manually pushing it up to horizontal. I examined the
> actuator rod and it does not appear bent or scored. It is stiff.
Can
> these be rebuilt or is it just better to get a new one? HWH web
site
> shows that actuator to be $150.00 OUCH ! I read where John Finn
had
> his whole system rebuilt for about $900 plus at the HWH factory.
Almost
> makes me want to do the whole works.
>
> Bruce 88 FC35
>
Quote this message in a reply
Post Reply 




User(s) browsing this thread: 1 Guest(s)