EMS 50C

[Gregory OConnor]

Rob , then there must be a transfer switch for the inverter after the
shore - genset transfer switch and closer to the Wanderlodge power
fuse pannel?????

GregoryO'Connor
94ptRomolandCa

--- In WanderlodgeForum@yahoogroups.com, "Rob Robinson"
wrote:
>
> My mistype Dan. I installed mine after not before the transfer
switch. I
> guess my inverter does not go through the transfer switch. When on
inverter
> I do not get any reading on the EMS display. I do get readings
while the gen
> or shore power are selected.
>
> On 25/03/07, ac7880 wrote:
> >
> > Rob,
> > If you wire the EMS before the transfer switch, you have to choose
> > one input for the EMS (shore or generator or invertor). There are
> > multiple inputs into the transfer switch(es), but should only be
one
> > output to the circuit breaker panel
> >
> > So for instance if you choose to use the shore power input into
the
> > EMS, generator and invertor are still available, but the coach is
> > not surge protected from the gen or invertor output.
> >
> > If you install after the transfer switch, shore, gen, invertor
power
> > introduction into the coach are all checked. I installed on the
> > shore cable just prior to the transfer switch due to easier
install
> > location with my setup, and also to ensure the two transfer
switches
> > are also protected from a shore power surge. I distrust the shore
> > power the most.
> >
> > Dan
> > 94 BB BMC 37' NM
> >
> > --- In WanderlodgeForum@yahoogroups.com 40yahoogroups.com>,
> > "Rob Robinson"
> > wrote:
> > >
> > > Bill as I understand it, if you have the EMS wired before the
> > Transfer
> > > Switch and either the shore power or the generator malfunction
the
> > > functional one will still be available. In other words, if the
> > genny started
> > > putting out funky power this would only cause the genny to be
> > obstructed.
> > > Correct shore power would still get through. Is this correct???
> > >
> > > On 25/03/07, Wilhelmus Schreurs wrote:
> > > >
> > > > Mike:
> > > > It also has a feature for frequency, so if the frequency or
> > voltage is out
> > > > of whack on the generator the contactor would not pull in.
> > > > Mike, everyone has there own reasons for doing things, and
IMHO,
> > I would
> > > > want the EMS to protect as much as it is capable of. Is this
EMS
> > the perfect
> > > > solution, no, but it is the best there is available that I
have
> > been able to
> > > > find.
> > > >
> > > > Bill 84 FC 35 SB "$quanderlodge"
> > > > Terrace, B.C. Canada
> > > >
> > > > ----- Original Message ----
> > > > From: mbulriss <mbulriss@ <mbulriss%40yahoo.com>>
> > > > To: WanderlodgeForum@yahoogroups.com 40yahoogroups.com> > > 40yahoogroups.com>
> > > > Sent: Sunday, March 25, 2007 1:56:44 PM
> > > > Subject: [WanderlodgeForum] Re: EMS 50C
> > > >
> > > > Bill,
> > > >
> > > > That's why mine is being installed (when I get to it) only on
the
> > > >
> > > > shore power, so I can still have gen set power.
> > > >
> > > > Mike Bulriss
> > > >
> > > > 1991 WB40 "Texas Minivan"
> > > >
> > > > San Antonio, TX
> > > >
> > > > --- In WanderlodgeForum@ yahoogroups. com, Wilhelmus Schreurs
> > > >
> > > >
> >
> >
> >
>
>
>
> --
> Rob, Sue & Merlin Robinson
> 94 WLWB
>
>
> [Non-text portions of this message have been removed]
>