I have a 1988 wbwl walk thriugh bath. in the overhead cabinet next to the
refrigerator is a panel that contains controls for genny odor controls. both
leds have gone bad. i am looking for replacements Any Ideas?
he is looking for numerical readouts not leds
Stephen 97bmc 37
--- In
WanderlodgeForum@yahoogroups.com, Wayne Kotila
wrote:
>
> If you have electical knowledge and are comfortable working with it, you can
buy L E Ds at Radio schack and solder new ones on the circuite board. If they
are not on a board and are connected with wires thats easier yet. Radio schack
has a variety of L E Ds in a variety of colors and a couple sizes (5mm or 10mm).
Some are in mounting rings that allowà them to snap into a mounting hole in a
panel and these are usually set up already for a certain voltage like 12 volt.
If you buy justà the L E D by itself, you will have toà solder a resistor to
theà positive wire from the L Eà D becauseà the L E D only usesà between 3 and
4 volts, usually for 12 volt a 1000 ohm resistor is what is needed. L E Ds are
positive/negative specific,Ã and if you are adding a resistor, solder it to the
positveà wire from the L Eà D. If you reverse the polarityà it doesn't damage
the L E D, ità just won't light.
> I hope this helps
> Ã
> Wayne kotila
> 96PT42Ã Ã
>
> --- On Tue, 9/28/10, jr wrote:
>
>
> From: jr
> Subject: [WanderlodgeForum] Led Tank and clock displays
> To: WanderlodgeForum@yahoogroups.com
> Date: Tuesday, September 28, 2010, 4:54 PM
>
>
> Ã
>
>
>
> I have a 1988 wbwl walk thriugh bath. in the overhead cabinet next to the
refrigerator is a panel that contains controls for genny odor controls. both
leds have gone bad. i am looking for replacements Any Ideas?
>
he is looking for numerical readouts not leds
Stephen 97bmc 37
--- In
WanderlodgeForum@yahoogroups.com, Wayne Kotila
wrote:
>
> If you have electical knowledge and are comfortable working with it, you can
buy L E Ds at Radio schack and solder new ones on the circuite board. If they
are not on a board and are connected with wires thats easier yet. Radio schack
has a variety of L E Ds in a variety of colors and a couple sizes (5mm or 10mm).
Some are in mounting rings that allowà them to snap into a mounting hole in a
panel and these are usually set up already for a certain voltage like 12 volt.
If you buy justà the L E D by itself, you will have toà solder a resistor to
theà positive wire from the L Eà D becauseà the L E D only usesà between 3 and
4 volts, usually for 12 volt a 1000 ohm resistor is what is needed. L E Ds are
positive/negative specific,Ã and if you are adding a resistor, solder it to the
positveà wire from the L Eà D. If you reverse the polarityà it doesn't damage
the L E D, ità just won't light.
> I hope this helps
> Ã
> Wayne kotila
> 96PT42Ã Ã
>
> --- On Tue, 9/28/10, jr wrote:
>
>
> From: jr
> Subject: [WanderlodgeForum] Led Tank and clock displays
> To: WanderlodgeForum@yahoogroups.com
> Date: Tuesday, September 28, 2010, 4:54 PM
>
>
> Ã
>
>
>
> I have a 1988 wbwl walk thriugh bath. in the overhead cabinet next to the
refrigerator is a panel that contains controls for genny odor controls. both
leds have gone bad. i am looking for replacements Any Ideas?
>
They sell almost any electronic component you could wish for. Radio shack doesn't havemany componentsany more.
Bill
Michigan
----- Original Message -----
From: "sbirtles@cogeco.ca"
To: "WanderlodgeForum@yahoogroups.com"
Sent: Tuesday, September 28, 2010 5:23 PM
Subject: [WanderlodgeForum] Re: Led Tank and clock displays
he is looking for numerical readouts not leds
Stephen 97bmc 37
--- In "WanderlodgeForum@yahoogroups.com", Wayne Kotila wrote:
>
> If you have electical knowledge and are comfortable working with it, you can buy L E Ds at Radio schack and solder new ones on the circuite board. If they are not on a board and are connected with wires thats easier yet. Radio schack has a variety of L E Ds in a variety of colors and a couple sizes (5mm or 10mm). Some are in mounting rings that allowÃthem to snap into a mounting hole in a panel and these are usually set up already for a certain voltage like 12 volt. If you buy justÃthe L E D by itself, you will have toÃsolder a resistor to theÃpositive wire from the L EÃD becauseà the L E D only usesÃbetween 3 and 4 volts, usually for 12 volt a 1000 ohm resistor is what is needed. L E Ds are positive/negative specific,Ãand if you are adding a resistor, solder it to the positveÃwire from the L EÃD. If you reverse the polarityÃit doesn't damage the L E D, itÃjust won't light.
> I hope this helps
> Ã
> Wayne kotila
> 96PT42ÃÃ
>
> --- On Tue, 9/28/10, jr wrote:
>
>
> From: jr
> Subject: [WanderlodgeForum] Led Tank and clock displays
> To: "WanderlodgeForum%40yahoogroups.com"
> Date: Tuesday, September 28, 2010, 4:54 PM
>
>
> Ã
>
>
>
> I have a 1988 wbwl walk thriugh bath. in the overhead cabinet next to the refrigerator is a panel that contains controls for genny odor controls. both leds have gone bad. i am looking for replacements Any Ideas?
>
i looked at digikey ,mouser,future electronics,and allied there was nothing
suitable
Stephen 97 BMC37
--- In
WanderlodgeForum@yahoogroups.com, "Bill Prestin"
wrote:
>
> You can purchase numerical readouts from: http://www.digikey.com/
>
> They sell almost any electronic component you could wish for. Radio shack
doesn't have many components any more.
>
> Bill
> Michigan
>
> ----- Original Message -----
> From: cape0001
> To: WanderlodgeForum@yahoogroups.com
> Sent: Tuesday, September 28, 2010 5:23 PM
> Subject: [WanderlodgeForum] Re: Led Tank and clock displays
>
>
>
> he is looking for numerical readouts not leds
> Stephen 97bmc 37
>
> --- In WanderlodgeForum@yahoogroups.com, Wayne Kotila wrote:
> >
> > If you have electical knowledge and are comfortable working with it, you
can buy L E Ds at Radio schack and solder new ones on the circuite board. If
they are not on a board and are connected with wires thats easier yet. Radio
schack has a variety of L E Ds in a variety of colors and a couple sizes (5mm or
10mm). Some are in mounting rings that allowà them to snap into a mounting hole
in a panel and these are usually set up already for a certain voltage like 12
volt. If you buy justà the L E D by itself, you will have toà solder a resistor
to theà positive wire from the L Eà D becauseà the L E D only usesà between 3
and 4 volts, usually for 12 volt a 1000 ohm resistor is what is needed. L E Ds
are positive/negative specific,Ã and if you are adding a resistor, solder it to
the positveà wire from the L Eà D. If you reverse the polarityà it doesn't
damage the L E D, ità just won't light.
> > I hope this helps
> > Ã
> > Wayne kotila
> > 96PT42Ã Ã
> >
> > --- On Tue, 9/28/10, jr wrote:
> >
> >
> > From: jr
> > Subject: [WanderlodgeForum] Led Tank and clock displays
> > To: WanderlodgeForum@yahoogroups.com
> > Date: Tuesday, September 28, 2010, 4:54 PM
> >
> >
> > Ã
> >
> >
> >
> > I have a 1988 wbwl walk thriugh bath. in the overhead cabinet next to the
refrigerator is a panel that contains controls for genny odor controls. both
leds have gone bad. i am looking for replacements Any Ideas?
> >
>