Wanderlodge Gurus - The Member Funded Wanderlodge Forum

Full Version: 86 PT40 turning radius?
You're currently viewing a stripped down version of our content. View the full version with proper formatting.

Greg Young

Anybody happen to know the actual turning radius of an 80s PT40? Looked in the
Blue Book and could not locate the info, and did a forum search and also came up
blank. We have to grade a ramp and a pad for our bird and it would be helpful
to know the geometry...

Thanks!
Greg Young
86 PT40 as yet un-re-named
Escondido, CA

sfedeli3

Hi Greg,

While I have never "measured" the radius with a tape, I usually
need 4 lanes and a wide berm to turn mine around. Assuming 12' lane
widths (and I am occupying one) that would put the outer radius of my
turning circle at around 60 feet, assuming that the wheels are turned
before starting into the turnabout. Now that you have brought it up,
I'll probably go to the nearest empty lot and find out! If you do the
same, please share it with us.

Shane Fedeli
85PT40
Hershey, PA

--- In WanderlodgeForum@yahoogroups.com, Greg Young wrote:
>
> Anybody happen to know the actual turning radius of an 80s PT40?
Looked in the Blue Book and could not locate the info, and did a forum
search and also came up blank. We have to grade a ramp and a pad for
our bird and it would be helpful to know the geometry...
>
> Thanks!
> Greg Young
> 86 PT40 as yet un-re-named
> Escondido, CA
>

Greg Young

We went out to an empty dirt lot (so we'd leave nice easy to measure tire
tracks). It's 85 feet full diameter, outside wheel to outside wheel, fully
locked. Bigger than you'd expect. I'll be interested to see if anyone comes up
with a different number - that seemed bigger than I expected.

In advance of eventually building a nice new pad and ramp to it on the property,
we now have our bird's front end perched on two home built ramps 18" up on one
side and 16" on the other. I'll post a pic to the group when I get a chance...

Hope everyone had fun in Georgia!

Greg Young
86 PT40 as yet un-re-named
Escondido, CA


----- Original Message ----
From: sfedeli3 <sfedeli3@...>
To: WanderlodgeForum@yahoogroups.com
Sent: Thursday, November 1, 2007 4:29:58 AM
Subject: [WanderlodgeForum] Re: 86 PT40 turning radius?

Hi Greg,

While I have never "measured" the radius with a tape, I usually
need 4 lanes and a wide berm to turn mine around. Assuming 12' lane
widths (and I am occupying one) that would put the outer radius of my
turning circle at around 60 feet, assuming that the wheels are turned
before starting into the turnabout. Now that you have brought it up,
I'll probably go to the nearest empty lot and find out! If you do the
same, please share it with us.

Shane Fedeli
85PT40
Hershey, PA

--- In WanderlodgeForum@ yahoogroups. com, Greg Young wrote:
>
> Anybody happen to know the actual turning radius of an 80s PT40?
Looked in the Blue Book and could not locate the info, and did a forum
search and also came up blank. We have to grade a ramp and a pad for
our bird and it would be helpful to know the geometry...
>
> Thanks!
> Greg Young
> 86 PT40 as yet un-re-named
> Escondido, CA
>




[Non-text portions of this message have been removed]

Howard O. Truitt

Greg,
Did you dump the tag axle before attempting the turn.
Howard T., Sowega, 86 PT40

----- Original Message -----
From: Greg Young
To: WanderlodgeForum@yahoogroups.com
Sent: Friday, November 02, 2007 3:24 PM
Subject: Re: [WanderlodgeForum] Re: 86 PT40 turning radius?


We went out to an empty dirt lot (so we'd leave nice easy to measure tire
tracks). It's 85 feet full diameter, outside wheel to outside wheel, fully
locked. Bigger than you'd expect. I'll be interested to see if anyone comes up
with a different number - that seemed bigger than I expected.

In advance of eventually building a nice new pad and ramp to it on the
property, we now have our bird's front end perched on two home built ramps 18"
up on one side and 16" on the other. I'll post a pic to the group when I get a
chance...

Hope everyone had fun in Georgia!

Greg Young
86 PT40 as yet un-re-named
Escondido, CA

----- Original Message ----
From: sfedeli3 <sfedeli3@...>
To: WanderlodgeForum@yahoogroups.com
Sent: Thursday, November 1, 2007 4:29:58 AM
Subject: [WanderlodgeForum] Re: 86 PT40 turning radius?

Hi Greg,

While I have never "measured" the radius with a tape, I usually
need 4 lanes and a wide berm to turn mine around. Assuming 12' lane
widths (and I am occupying one) that would put the outer radius of my
turning circle at around 60 feet, assuming that the wheels are turned
before starting into the turnabout. Now that you have brought it up,
I'll probably go to the nearest empty lot and find out! If you do the
same, please share it with us.

Shane Fedeli
85PT40
Hershey, PA

--- In WanderlodgeForum@ yahoogroups. com, Greg Young wrote:
>
> Anybody happen to know the actual turning radius of an 80s PT40?
Looked in the Blue Book and could not locate the info, and did a forum
search and also came up blank. We have to grade a ramp and a pad for
our bird and it would be helpful to know the geometry...
>
> Thanks!
> Greg Young
> 86 PT40 as yet un-re-named
> Escondido, CA
>

[Non-text portions of this message have been removed]






------------------------------------------------------------------------------


No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.486 / Virus Database: 269.15.19/1105 - Release Date: 11/2/2007
11:04 AM


[Non-text portions of this message have been removed]

Greg Young

Nope -forgot to. Tag axle was down. And probably will not attempt again for a
while now that we are parked.

Howard O. Truitt wrote:
> Greg,
> Did you dump the tag axle before attempting the turn.
> Howard T., Sowega, 86 PT40
> ----- Original Message -----
> From: Greg Young
> To: WanderlodgeForum@ yahoogroups. com
> Sent: Friday, November 02, 2007 3:24 PM
> Subject: Re: [WanderlodgeForum] Re: 86 PT40 turning radius?
> We went out to an empty dirt lot (so we'd leave nice easy to measure tire
tracks). It's 85 feet full diameter, outside wheel to outside wheel, fully
locked. Bigger than you'd expect. I'll be interested to see if anyone comes up
with a different number - that seemed bigger than I expected.
> In advance of eventually building a nice new pad and ramp to it on the
property, we now have our bird's front end perched on two home built ramps 18"
up on one side and 16" on the other. I'll post a pic to the group when I get a
chance...
> Hope everyone had fun in Georgia!
> Greg Young
> 86 PT40 as yet un-re-named
> Escondido, CA
> ----- Original Message ----
> From: sfedeli3 < sfedeli3@comcast. net >
> To: WanderlodgeForum@ yahoogroups. com
> Sent: Thursday, November 1, 2007 4:29:58 AM
> Subject: [WanderlodgeForum] Re: 86 PT40 turning radius?
> Hi Greg,
> While I have never "measured" the radius with a tape, I usually
> need 4 lanes and a wide berm to turn mine around. Assuming 12' lane
> widths (and I am occupying one) that would put the outer radius of my
> turning circle at around 60 feet, assuming that the wheels are turned
> before starting into the turnabout. Now that you have brought it up,
> I'll probably go to the nearest empty lot and find out! If you do the
> same, please share it with us.
> Shane Fedeli
> 85PT40
> Hershey, PA
> --- In WanderlodgeForum@ yahoogroups. com, Greg Young wrote:
> >
> > Anybody happen to know the actual turning radius of an 80s PT40?
> Looked in the Blue Book and could not locate the info, and did a forum
> search and also came up blank. We have to grade a ramp and a pad for
> our bird and it would be helpful to know the geometry...
> >
> > Thanks!
> > Greg Young
> > 86 PT40 as yet un-re-named
> > Escondido, CA
> >
> [Non-text portions of this message have been removed]
> ------------ --------- --------- --------- --------- --------- -
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.486 / Virus Database: 269.15.19/1105 - Release Date: 11/2/2007
11:04 AM
> [Non-text portions of this message have been removed]
>
Reference URL's