09-07-2015, 19:29
AL,
I'm not sure what you're asking for. Part #s for the PTO changeover or Part #s for the Hayden fan controls??
If you asking about the Hayden fan related controls. Yes, I did install two (2) new fans on the Hayden oil cooler. Part # 3680 fan @ $148 bucks each. We also made a better bracket to mount these 2 fans to the oil cooler.They do require a little different designed bracket than the original fans did. I replaced the hoses to & from the oil cooler.
I also replaced the #8037090P Temp/Sensor Switch on the bottom of the hydraulic oil reservoir. Price was $99.
The rest of the controls consist of an inline 30a fuse and the Hayden relay located in the panel in the engine bay.
Here's some info I copied from an earlier related post on the parts neede to change your 7/8" PTO to a 1'" wet splined PTO.
__________________________________________________________________________________________________
Here’s the cost comparison between buying a new 1” PTO and rebuilding your 7/8” greasable PTO into a 1” wet splined PTO’
I was quoted $1800 for a new 1” wet splined PTO.
David paid $675 for a 1” greasable PTO.
I am not aware of any difference between the two PTO(s) above as you can convert a greasable 1” PTO to a wet splined PTO simply by installing the Chelsea #328591-129x kit. I probably paid full retail as that was the price the manufacturer (Chelsea) quoted me.
I also paid more than David did for the 1” pump from CPC.
I paid $1482 for the CPC1049 pump.
David paid $795 for the same pump.
To rebuild the 7/8” PTO to 1” requires the following replacement parts;
1 CHE-328274 PTO closed end cap = $52.36
1 CHE-550397 1”i.d. bearing = $26.08
1 CHE-550532 1” i.d. bearing = 28.65
2 CHE-550439 1” i.d. bearing = 45.62
1 CHE-35-P-7 Gasket = 5.95
Total Parts = $ 198.33
PTO rebuild labor = 245.00
Total cost = $ 443.33 As compared to David’s cost of $675 for a new 1” PTO
_________________________________________________________________________________________________________________________________
If we use David’s cost on the 1" pump and rebuild the PTO, the total cost to convert from a 7/8” greasable PTO to a 1” wet spline PTO is:
1 CPC1049 1”pump $795.00
1 Rebuild of 7/8” to 1” PTO 443.33 (see above for parts required)
1 328591-129X wet spline kit $326.65
Totals $1564.98
Add Labor costs
Add the cost of hydraulic oil and filters and transmission fluid loss replacement.
I'm not sure what you're asking for. Part #s for the PTO changeover or Part #s for the Hayden fan controls??
If you asking about the Hayden fan related controls. Yes, I did install two (2) new fans on the Hayden oil cooler. Part # 3680 fan @ $148 bucks each. We also made a better bracket to mount these 2 fans to the oil cooler.They do require a little different designed bracket than the original fans did. I replaced the hoses to & from the oil cooler.
I also replaced the #8037090P Temp/Sensor Switch on the bottom of the hydraulic oil reservoir. Price was $99.
The rest of the controls consist of an inline 30a fuse and the Hayden relay located in the panel in the engine bay.
Here's some info I copied from an earlier related post on the parts neede to change your 7/8" PTO to a 1'" wet splined PTO.
__________________________________________________________________________________________________
Here’s the cost comparison between buying a new 1” PTO and rebuilding your 7/8” greasable PTO into a 1” wet splined PTO’
I was quoted $1800 for a new 1” wet splined PTO.
David paid $675 for a 1” greasable PTO.
I am not aware of any difference between the two PTO(s) above as you can convert a greasable 1” PTO to a wet splined PTO simply by installing the Chelsea #328591-129x kit. I probably paid full retail as that was the price the manufacturer (Chelsea) quoted me.
I also paid more than David did for the 1” pump from CPC.
I paid $1482 for the CPC1049 pump.
David paid $795 for the same pump.
To rebuild the 7/8” PTO to 1” requires the following replacement parts;
1 CHE-328274 PTO closed end cap = $52.36
1 CHE-550397 1”i.d. bearing = $26.08
1 CHE-550532 1” i.d. bearing = 28.65
2 CHE-550439 1” i.d. bearing = 45.62
1 CHE-35-P-7 Gasket = 5.95
Total Parts = $ 198.33
PTO rebuild labor = 245.00
Total cost = $ 443.33 As compared to David’s cost of $675 for a new 1” PTO
_________________________________________________________________________________________________________________________________
If we use David’s cost on the 1" pump and rebuild the PTO, the total cost to convert from a 7/8” greasable PTO to a 1” wet spline PTO is:
1 CPC1049 1”pump $795.00
1 Rebuild of 7/8” to 1” PTO 443.33 (see above for parts required)
1 328591-129X wet spline kit $326.65
Totals $1564.98
Add Labor costs
Add the cost of hydraulic oil and filters and transmission fluid loss replacement.